 |
|
|
|
| |
 |
| Engine
Accy's |
 |
|
|
|
|
| |
Air
Breathers |
 |
Oval
(Chrome) |
Small
- 8 3/8" wide x 11 7/8" long x 3" tall, #6020c |
$80.95 |
| Large
- 8 1/4" wide x 15" long x 3" tall, #6021c |
$90.95 |
| |
|
|
|
 |
Round
(Polished) |
14 7/16"
outside diameter & stands off car 4 1/4".
Uses common 14" x 3" filter elements.
Raised bottom base fits all cars with 5 1/8" neck.
#8429 |
$44.95 |
|
|
| Top of Page |
| |
| Valve
Covers |
 |
Pre
'87
(side bolts)
(Chrome) |
Short (2 1/2") or Tall (3 3/4"), Ball Milled
Each cover has one 1 1/4" diameter hole for engine breather
or PCV valve.
Short - #6131c
Tall - #6130c |
$101.95 |
'87
& Later
(center bolt)
(Chrome) |
Short (2 1/2"), Ball Milled
Each cover has one 1 1/4" diameter hole for engine breather
or PCV valve, #6037c |
$131.95 |
 |
'87 & Later
(center bolt)
(Chrome) |
Small Block Chevy Flamed aluminum
valve covers, center bolt, includes baffles. (does not incude breathers
shown)
Short, 2-1/2", #8561c |
$130.95 |
 |
Pre
'87
(side bolts)
(Polished) |
Die cast polished aluminum small
block Chevy valve covers. Covers are not internally baffed. Baffled
grommets are recommeded.
Short, 2-1/2", #8484 |
$79.95 |
'87 & Later
(center bolt)
(Polished) |
Die cast polished aluminum small
block Chevy valve covers. Covers are not internally baffed. Baffled
grommets are recommeded.
Short, 2-1/2", #8461 |
$95.95 |
 |
Valve
Cover Breathers & PCV Valves
(Chrome) |
Machined
from aluminum then chrome plated.
All have 1" diameter base for installation into valve cover grommet.
PCV valve has push-on connection for 3/8" vacuum hose. |
|
 Smooth Top - w/PCV valve, #6000c |
$41.95 |
| Smooth Top - Breather, #6001c |
$36.95 |
| Ball Milled- w/PCV
valve, #6100c |
$41.95 |
| Ball Milled- Breather,
#6101c |
$36.95 |
 |
Baffled
Grommets
#5425 |
Fits
1 1/4" valve cover hole, pair |
$2.95 |
 |
Hole
Plug
#6375 |
Molded from neoprene to ensure positive oil seal.
Made to fit most stamped or die cast valve covers. Valve cover plugs,
1-1/4" O.D. Dia
2 per pack. |
$3.95 |
 |
Bolt-In
baffle kit
#S6034 |
Screws
to inside of valve cover, pair |
$8.95 |
|
| NOTE: Covers are not baffled |
|
| Top of Page |
| |
| Water
Necks |
Die cast aluminum
thermostat housings with O-ring seal, 360° swivel
(In polished & chrome) |
Straight
up, 3" tall, polished, 6002 |
$24.95 |
| 45°
swivel, polished, #6003 |
$29.00 |
| 90°
swivel, polished, #6009 |
$30.95 |
| Straight
up, 3" tall, chrome, #6002c |
$36.95 |
| 45°
swivel, chrome, #6003c |
$40.95 |
| 90°
swivel, chrome, #6009c |
$39.95 |
 |
Street
& Performance 360°/10° swivel, works with TPI, also works
great for any application where a 45° neck has a clearance problem.
Works great on 40's & later vehicles. |
Pol |
$75.00 |
| Chrm |
$85.00 |
 |
LT-1
water neck Type I, gives a little more room between radiator &
hose, 35° closer to engine. |
Pol |
$75.00 |
| Chrm |
$90.00 |
 |
LT-1
water neck Type II, this puts the water neck in approx. the same position
as stock. |
Pol |
$75.00 |
| Chrm |
$90.00 |
 |
LS-1
water neck, Straight, O-ring seal w/thermostat |
Pol |
$75.00 |
 |
LS-1
water neck, 360°/45-15° swivel, O-ring seal w/thermostat |
Pol |
$95.00 |
|
|
| Top of Page |
| |
| Small
Block Chevy Intakes |
|
Polished
SB Chevy Performance Street Manifold, Non-EGR, Fits 1957-'95 engines.
The Power+Plus PS manifold is the ideal street manifold. Can use stock
Quadra-Jet carb or 500-659 cfm vacuum secondary carbs.
Dual plane design - Provides outstanding power from idle to
5,500 rpm.
#52000 |
Pol |
$155.95 |
 |
Polished
SB Chevy High Performance Street Manifold, Non-EGR, Fits 1957-'95
engines.
The Power+Plus HPS manifold is the ideal street manifold. Designed
to be used with Holley, Carter AFB, Edelbrock square bore carbs. For
street use 600-700 cfm vacuum secondary carbs. For high performance
street use 700-800 cfm double pumper.
Dual plane design - Provides outstanding power from idle to
1,500 to 6500 rpm.
#52020 |
Pol |
$171.95 |
|
|
| Top of Page |
| |
  |
| |
To order any item on our site:
Call: (864) 269-6813
or
E-Mail: rodshop@carolinarodshop.com |
|
|
